HS5157 Front Mount Hydraulic Steering Cylinder Seal Kit & Bleed Kit for Seastar

Description: Front Moun t Hydraulic Steering Cylinder Seal Kit & Bleed Kit For Seastar HS5157 Note: Blue and orange warehouses are shipped randomly. If you have special requirements for color, please contact us in advance. Description: 100% New Made from high quality material. the Bridge Tube Now Comes with Hose Clamps for a Perfect Fit. Easy to install to save your time. O ne Person Easily Controls the Bleed Process from End to End. According to original factory specifications, perfect match to original car. Parts are from certified professional factory. Replacement Front Seal Kit for Seastar Pivot / Front Mount Cylinders. Used to Repair Leaking or Weeping Cylinder Seals. Changing out Fluid Bottles Is Quick and Clean. Entire Steering System Remains Sealed During the Bleed Process from End to End, Ensuring That Fluid Goes Where It Is Supposed to Go，Failure to Replace a Damaged Steering Cylinder Will Result in Seal Failure and Possible Loss of Steering. Replacement For: For Seastar Hydraulic Steering Systems, Hs5157 Kit Fits Front Mount Cylinder Parts: Hc5340, Hc5341, Hc5342, Hc5343, Hc5344, Hc5345, Hc5346, Hc5347, Hc5348, Hc5358, Hc5365, Hc5375, Hc5394, Hc5445, Hc6750, Hc6751, Hc6752, Hc6753, Hc6754, Hc6755 Basic Instructions: 1. Attach bottle to helm reservoir (do not pierce bottle)(do not let bottle run empty) 2. Connect bridge tube to bleed fittings on steering cylander and loosen/open fittings. 3. Use helm to pump fluid through system by turning the wheel in one direction. Air bubbles will be pushed to the reservoir at the helm. 4. Manually swing the outboard through full articulation to relieve trapped air and confirm good bleed. Note: Orientating bleed fittings up while pumping fluid with helm will allow air to escape cylinder. 5. Repeat 3-4 as necessary until no air is visible in bridge tube. 6. Tighten bleed fittings before removing bridge tube Using Instruction: 1. Loosening the Seal Gland. Turn the outboard hard to port; place the pin wrench in the holes of a gland. And use a 5⁄8-inch box wrench on the nut on the port end of the piston rod. (NOTE:Turn counterclockwise on the pin wrench with opposite pressure on the box wrench to loosen the seal gland) 2. Removing the Support Bracket. Use a 3/4-inch socket wrench to remove the nut and washer securing the support bracket to the support rod. (Do the same to the piston rod nut and washer. ) Use wrenches on the opposite ends to keep the rods from turning. With hardware gone, pull off the support bracket. Use the pin wrench to remove the Old Seal Gland. 3. Install the New Seal Gland. Place the tapered guide tool from the kit on the end of the piston rod and lubricate it and the piston rod well with oil or grease. Carefully slide the new seal gland over the guide and onto the piston rod until it reaches the cylinder. Screw the seal gland into the cylinder, but don't tighten it yet. Remove the guide tool; it is not part of the final assembly, but you will need it for the other side. 4 . Reinstall the Support Bracket. Reconnect the support bracket to the support rod and piston rod and replace the washers and nuts, tightening the nuts against the washers. You may need to use wrenches on the opposite nuts to tighten sufficiently. 5 . Tightening the New Seal Gland. Use the pin wrench to tighten the new seal gland while using a 5⁄8-inch box wrench on the starboard end of the piston rod for counter torque. Package Included: 1 X Hose with Screw Cap 1 X Bridge Tube That Connects to Bleed Fittings. 2 X Seal Glands 1 X Seal Gland Assembly Guide Tool 1 X Pin Holder 8 X Varies O-rings Shipping We process your order within 1 business day upon payment (Note: NOT counting holidays or weekends). We only ship to the confirmed address provided by ebay. Before you pay, please make sure your address in ebay matches the address you would like us to ship to. We strive our best to provide you the most reliable, affordable way of shipping service. But sometimes delivery is highly depended on the courier company. If you do not receive your item on time, please contact us immediately for further assistance. Thank you for your understanding. Return & Refund We operate a 30 day money back guarantee. Please read the item description and check the pictures carefully before bidding. Return or refund is available only if item DOA or there's error in item description causing the item not fitting your need. In such cases, seller pays for all related shipping cost if any. Returns are also acceptable if buyer purchased this by mistake and item still in good condition for reselling. Buyer is responsible for all related shipping cost. We maintain high standards of excellenceandstrive for 100% customer satisfaction!Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback , so that we can satisfactorily address your concerns. Feedback We maintain high standards of excellenceandstrive for 100% customer satisfaction!Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concern

Price: 36.99 USD

Location: Chino, California

End Time: 2024-07-29T07:28:14.000Z

Shipping Cost: 0 USD