Matek CRSF to PWM Converter CRSF-PWM-6/CRSF-PWM-C for TBS Nano RX SE Drone

Description: NEW Original Matek CRSF to PWM Converter CRSF-PWM-6 / CRSF-PWM-C for TBS Crossfire Nano RX SE RC FPV Racing Drones Parts DIY Parameters:CRSF-PWM-6:Compatible with CRSF protocol receiver only6x PWM outputsPWM frequency configurable (50Hz default, 100,160,330, 400Hz)2x UARTs (for Receiver and GPS)Telemetry ID: RxBt, Curr, Capa, Bat%, GPS, GSpd, Hdg, Alt, Sats36V Max. battery voltage sense (1K:10K voltage divider built-in)Compatible with external Current sensor (0~3.3V)Vbat and Current sensor scale configurableFailsafe value auto setFirmware upgradeableRated voltage: 4~9V @5V pad, 0~36V @Vbat, 0~3.3V @CurrNo 5V regulator built-in25mm x 16mm, 1.3gPacking: 1x CRSF-PWM-6, Dupont 2.54 pinsCRSF-PWM-C:Compatible with CRSF protocol receiver only10x PWM outputsPWM frequency configurable (50Hz default, 100,160,330, 400Hz)2x UARTs (for Receiver and GPS)Telemetry ID: RxBt, Curr, Capa, Bat%, GPS, GSpd, Hdg, Alt, Sats36V Max. battery voltage sense (1K:10K voltage divider built-in)Current sensor built-in (90A continuous /220A Peak), current scale = 150 by defaultVbat and Current sensor scale configurableFailsafe value auto setFirmware upgradeableRated voltage: 4~9V @5V pad, 0~36V @BAT+No 5V regulator built-in26mm x 26mm, 2.8gPacking: 1x CRSF-PWM-C, 1x low ESR capacitor, Dupont 2.54 pinsPinouts and Pads:Tx1/Rx1(UART1) for CRSF protocol ReceiverTx2/Rx2(UART2) for GPS/firmware update/setting parameters1~10: CH1~CH10 PWM outputsCurr: current sensor signal (0~3.3V)Vbat: Battery voltage sensing (0~36V)G: ground4v5 pad voltage = 5V pad voltage -0.3V, make sure the voltage on 5V pad is not higher than receiver and GPS rated voltage.Failsafe:Failsafe value is set automatically after CRSF-PWM board is powered on and receive CRSF signal. LED blinks 8 times quickly.Failsafe value = The PWM value of each channel(except CH3) when CRSF signal is received by CRSF-PWM board for the first timeCH3 is specially arranged for the throttle, Failsafe value = 988 by default.Usually put the Throttle joystick to the lowest point, put AIL(Roll), ELE(Pitch), RUD(Yaw) middle before powering on receiver.LED status:slow blinks: CRSF-PWM board doesnt receive CRSF signal, e.g., receiver is not bound with transmitter, receiver is not connected to UART1 of CRSF-PWM board.8x quick blinks: CRSF-PWM board received CRSF signal and failsafe value is saved.solid ON: CRSF-PWM board and receiver are working normally2x slow blinks between 8x fast blink and solid on: CLI mode is activeGPS telemetry:Compatible with GPS NMEA protocolGPS "TX" to CRSF-PWM board "RX" Single wire half duplex UART connection, CRSF-PWM board "TX" to GPS "RX" is not essential.Support GPS Telemetry ID: GPS, GSpd, Hdg, Alt, Satsu-blox series GPS can output "0+1 – UBX+NMEA" protocol by defaultSensors(GPS, GSpd, Hdg, Alt, Sats) will blink in Transmitter TELEMETRY tab once CRSF-PWM board has connection with GPS.Troubleshooting for no GPS telemetry, double check the wiring between GPS and CRSF-PWM board, some u-blox GPS may dont output NMEA protcol, you need to be reverted GPS to default configuration in u-center.TIM & PWM Frequency:PWM frequency on all 10x Channels can be configured according to TIMPWM run at 50Hz by defaultTIM2: CH1, CH2, CH4TIM16: CH3TIM3: CH5, CH6, CH7, CH8TIM1: CH9, CH10CLI mode:If CRSF-PWM board doesnt detect GPS connected to UART2 within 10 seconds after powering on, CLI mode will active.After CLI mode is active, CRSF-PWM board can be connected to configurator via USB-TTL module/FC passthrough.in CLI mode, CRSF-PWM board firmware can be updatedCLI mode has no effect to receiver CRSF signal and PWM outputsCRSF-PWM-6:Compatible with CRSF protocol receiver only6x PWM outputsPWM frequency configurable (50Hz default, 100,160,330, 400Hz)2x UARTs (for Receiver and GPS)Telemetry ID: RxBt, Curr, Capa, Bat%, GPS, GSpd, Hdg, Alt, Sats36V Max. battery voltage sense (1K:10K voltage divider built-in)Compatible with external Current sensor (0~3.3V)Vbat and Current sensor scale configurableFailsafe value auto setFirmware upgradeableRated voltage: 4~9V @5V pad, 0~36V @Vbat, 0~3.3V @CurrNo 5V regulator built-in25mm x 16mm, 1.3gPacking: 1x CRSF-PWM-6, Dupont 2.54 pinsCRSF-PWM-C:Compatible with CRSF protocol receiver only10x PWM outputsPWM frequency configurable (50Hz default, 100,160,330, 400Hz)2x UARTs (for Receiver and GPS)Telemetry ID: RxBt, Curr, Capa, Bat%, GPS, GSpd, Hdg, Alt, Sats36V Max. battery voltage sense (1K:10K voltage divider built-in)Current sensor built-in (90A continuous /220A Peak), current scale = 150 by defaultVbat and Current sensor scale configurableFailsafe value auto setFirmware upgradeableRated voltage: 4~9V @5V pad, 0~36V @BAT+No 5V regulator built-in26mm x 26mm, 2.8gPacking: 1x CRSF-PWM-C, 1x low ESR capacitor, Dupont 2.54 pinsPinouts and Pads:Tx1/Rx1(UART1) for CRSF protocol ReceiverTx2/Rx2(UART2) for GPS/firmware update/setting parameters1~10: CH1~CH10 PWM outputsCurr: current sensor signal (0~3.3V)Vbat: Battery voltage sensing (0~36V)G: ground4v5 pad voltage = 5V pad voltage -0.3V, make sure the voltage on 5V pad is not higher than receiver and GPS rated voltage.Failsafe:Failsafe value is set automatically after CRSF-PWM board is powered on and receive CRSF signal. LED blinks 8 times quickly.Failsafe value = The PWM value of each channel(except CH3) when CRSF signal is received by CRSF-PWM board for the first timeCH3 is specially arranged for the throttle, Failsafe value = 988 by default.Usually put the Throttle joystick to the lowest point, put AIL(Roll), ELE(Pitch), RUD(Yaw) middle before powering on receiver.LED status:slow blinks: CRSF-PWM board doesnt receive CRSF signal, e.g., receiver is not bound with transmitter, receiver is not connected to UART1 of CRSF-PWM board.8x quick blinks: CRSF-PWM board received CRSF signal and failsafe value is saved.solid ON: CRSF-PWM board and receiver are working normally2x slow blinks between 8x fast blink and solid on: CLI mode is activeGPS telemetry:Compatible with GPS NMEA protocolGPS "TX" to CRSF-PWM board "RX" Single wire half duplex UART connection, CRSF-PWM board "TX" to GPS "RX" is not essential.Support GPS Telemetry ID: GPS, GSpd, Hdg, Alt, Satsu-blox series GPS can output "0+1 – UBX+NMEA" protocol by defaultSensors(GPS, GSpd, Hdg, Alt, Sats) will blink in Transmitter TELEMETRY tab once CRSF-PWM board has connection with GPS.Troubleshooting for no GPS telemetry, double check the wiring between GPS and CRSF-PWM board, some u-blox GPS may dont output NMEA protcol, you need to be reverted GPS to default configuration in u-center.TIM & PWM Frequency:PWM frequency on all 10x Channels can be configured according to TIMPWM run at 50Hz by defaultTIM2: CH1, CH2, CH4TIM16: CH3TIM3: CH5, CH6, CH7, CH8TIM1: CH9, CH10CLI mode:If CRSF-PWM board doesnt detect GPS connected to UART2 within 10 seconds after powering on, CLI mode will active.After CLI mode is active, CRSF-PWM board can be connected to configurator via USB-TTL module/FC passthrough.in CLI mode, CRSF-PWM board firmware can be updatedCLI mode has no effect to receiver CRSF signal and PWM outputs

Price: 11.43 USD

Location: 深圳

End Time: 2024-04-22T05:05:19.000Z

Shipping Cost: 2 USD