Description: This item is New Open BoxSpecificationsProduct NameSpeedyBee F405 WING MINI FC boardMCUSTM32F405, 168MHz, 1MB FlashIMU(Gyro&Accelerometer)ICM-42688-PBarometerSPL006-001OSD ChipAT7456EBlackboxMicroSD Card SlotUART6 sets (USART1, USART2, USART3, UART4, UART5,UART6 - Dedicated for Wireless board Telemetry connection)I2C1x Used for magnetometer, digital airspeed sensorADC4x (VBAT, Current, Analog RSSI, Analog AirSpeed)PWM12x (9x pin headers + 2x solder pads + 1x "LED" pad)ELRS/CRSF ReceiverSupported, connected to UART1SBUSBuilt-in inverter for SBUS input (UART2-RX)LED3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator (Red)Analog RSSISupported, Named as "RS"Dual Analog Camera SwitchingDefault to Camera1 Video Input (C1). Switch between C1 and C2 using ArduPilot Relay or INAV Modes/USER.Both cameras should have the same video format, either PAL or NTSC.Supported FC FirmwareINAV: SpeedyBeeF405WING (default)ArduPilot: SpeedyBeeF405WINGWeight5.6g Product NameSpeedyBee F405 WING MINI PDB boardInput voltage range7~26V (2~6S LiPo)Battery Voltage SensorConnect to FC board VBAT, 1K:10K (Scale 1100 in INAV, BATT_VOLT_MULT 11.0 in ArduPilot)Battery Current Sensor80A continuous, 150A peak Connect to FC board Current (Scale 195 in INAV, 50 A/V in ArduPilot)TVS Protective diodeYesFC BEC outputOutput 5.2V +/- 0.1V DC Continuous current 2 Amps, 3A Peak Designed for FC, Receiver, GPS module, AirSpeed Sensor, Telemetry moduleVTX & Camera power supplyThe VTX power interface Vv offers two power supply options: direct battery voltage or integrated BEC 5V (sharing the 5V4A Servo BEC voltage)By default, it is set to battery voltage(Ensure the VTX and camera input voltage range is compatible)Switching to 5V power supply is possible via pad jumper (using Servo BEC output)(If using this method, ensure the current requirements for both servo and VTX are sufficient)Servo BEC outputOutput 5V +/- 0.1V DC Continuous current 4 Amps, 5A Peak Voltage adjustable, 5V Default, 6V via jumper Designed for Servos.Weight5.5g Product NameSpeedyBee F405 WING MINI Wireless USB ExtenderWireless Configuration (long press BOOT button for 6 seconds to switch modes)INAV:Please make sure the MSP switch on UART 6 is turned on and set to a baud rate of 115200 ArduPilot:Please make sure the Serial 6 is set to baud rate 115200 and protocol Mavlink2BLE mode, connect to Speedybee APPWi-Fi (AP)mode, able to connect to Speedybee APP, QGroundControl APP, MissionPlanner, etc. WiFi: Speedybee eFLY-WIFI Password: 88888888Wi-Fi (STA)mode, able to connect to QGroundControl APP, MissionPlanner, etc.Step 1: turn on Personal Hotspot;Step 2: Set hotspot, locate NAME/Device Name/Hotspot name/etc.Step 3: change the current name to eFLY and the password is, 88888888Wireless off modeUSB Port TypeType-CBuzzer5V Active BuzzerWeight3.2g
Price: 40 USD
Location: Herndon, Virginia
End Time: 2024-12-25T23:27:06.000Z
Shipping Cost: N/A USD
Product Images
Item Specifics
All returns accepted: ReturnsNotAccepted
Type: Flight Controller
Model: SpeedyBee F405 WING
